TurboLamik TurboLamik

Parameters / Output

Output

The TCU output pins: PWM channels, reverse and neutral outputs, and what each one drives.

49 parameters: 11 documented, 20 covered by a family note, 18 not yet documented. 5 of the undocumented ones carry the vendor's own description and nothing else. 5 exist only on firmware 10.77. 1 were removed at 10.76.

49 parameters

Drive/In Gear Output signal

# 0x2869 1×1
Picks the AUX pin that goes active while the box is in Drive (1-12, 0 = off). Pairs with the Neutral and Reverse outputs (AUX11 pin 56 and AUX12 pin 57 in most base maps) to drive gear-state indicators, which matters on paddle-only builds with no PRND lever.
Manual: Wiring & pinout See also: Neutral Output · Reversee Output · Parking Output
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 - OFF

From the official base maps what they contain, not what it does

Official base maps ship 0 on 8HP50, 8HP51, 8HP70, 8HP75; 255 on 8HP45, 8HP90.

Address
0x1FA6 8102
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Drive Output

Enable Neutral Output in parking

# 0x5D92
No explanation exists yet.

From the official base maps what they contain, not what it does

On in all 16 official base maps.

Detail
Address
0x1EEB 7915
Width
8-bit
Mask
0x8
Firmware
10.75, 10.77
10.75 name
Enable Neutral Output in Park

Ignition (wake up output)

# family 0x34C1 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 - OFF

From the official base maps what they contain, not what it does

Every official base map ships 8.

Address
0x17EB 6123
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Ignition (wake up out)

Line Lock Valve Output

# family 0x41D4 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 - OFF

From the official base maps what they contain, not what it does

Official base maps ship 0 on 8HP45, 8HP50, 8HP70, 8HP75, 8HP90; 12 on 8HP51.

Address
0x17BB 6075
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

Neutral Output

# family 0x791E 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 - OFF

From the official base maps what they contain, not what it does

Official base maps ship 11 on 8HP45, 8HP50, 8HP70, 8HP75, 8HP90; 0 on 8HP51.

Address
0x17B6 6070
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

Oil Cooler Fan Output

# family 0x457F 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 - OFF

From the official base maps what they contain, not what it does

Every official base map ships 1.

Address
0x17B8 6072
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Oil Fan Output

Oil Cooler Fan Temp Setting

# 0x27FE 1×2
No explanation exists yet.

From the official base maps what they contain, not what it does

Values differ between official base maps (2 distinct variants); across all 16 they span 70 to 85.

Detail
Address
0xE66 3686
Size
1×2 cells
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Oil Temp Fan

Parking Output

# 0x7F8E 1×1
Picks the AUX pin that goes active in Park (1-12, 0 = off). Park engages automatically on power-down, or via a dedicated park button on the Parking Signal Input; this output is how the rest of the car finds out.
Manual: Wiring & pinout See also: Drive/In Gear Output signal · Neutral Output
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 - OFF

From the official base maps what they contain, not what it does

Official base maps ship 7 on 8HP70, 8HP75; 0 on 8HP45, 8HP50, 8HP51, 8HP90.

Address
0x1F44 8004
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

Reversee Output

# family 0x5734 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 - OFF

From the official base maps what they contain, not what it does

Official base maps ship 12 on 8HP45, 8HP50, 8HP70, 8HP75, 8HP90; 0 on 8HP51.

Address
0x17B7 6071
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Reverse Output

Switch Mux Output

# family 0x7146 3×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 to 20 - Virtual Aux 13-20

From the official base maps what they contain, not what it does

Every official base map ships 0 in all 3 cells.

Address
0x1DDF 7647
Size
3×1 cells
Width
8-bit
Firmware
10.75, 10.77
10.75 name
SW Mux Out

Traction Control OFF Output

# family 0x1685 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 - OFF

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x17BC 6076
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

TransBrake/Launch Control Output

# family 0x2DBA 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 - OFF

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x17BA 6074
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77
10.75 name
T-Brake/Launch Output

Vss Multiplier (Inpulse Calibration)

# 0x6A3B 1×1
No explanation exists yet.

From the official base maps what they contain, not what it does

Official base maps ship 4 on 8HP50, 8HP51, 8HP70, 8HP75, 8HP90; 17 on 8HP45.

Detail
Address
0x1800 6144
Size
1×1 value
Width
16-bit
Firmware
10.75, 10.77
10.75 name
VSS Multiplier

Vss Output

# Vendor description only 0x7F27 1×1

TurboLamik XDF

0 - 8 OFF 9 to 12 - Aux 9 to 12 13 - OFF

From the official base maps what they contain, not what it does

Official base maps ship 9 on 8HP50, 8HP51, 8HP70, 8HP75, 8HP90; 0 on 8HP45.

Detail
Address
0x17F0 6128
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77
10.75 name
VSS Output

Wake up out time ON

# 10.75 onlyremoved at 10.76 0x333F 1×1
Not documented yet.
Detail
Address
0x1B84 7044
Size
1×1 value
Width
8-bit
Firmware
10.75

Wake up output delay

# 0x4B80 2×1
No explanation exists yet.

From the official base maps what they contain, not what it does

Every official base map ships 0.

Detail
Address
0x1B83 7043
Size
2×1 cells
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Wake up out time OFF

Wake up output ON RPM

# Vendor description only 0x39A6

TurboLamik XDF

Do not turn off while engine is running (RPM > 0)

From the official base maps what they contain, not what it does

On in all 16 official base maps.

Detail
Address
0x17EF 6127
Width
8-bit
Mask
0x80
Firmware
10.75, 10.77
10.75 name
Wake up out ON RPM

Wake up output time t/10

# 0x5D96
No explanation exists yet.

From the official base maps what they contain, not what it does

Off in all 16 official base maps.

Detail
Address
0x1D71 7537
Width
8-bit
Mask
0x20
Firmware
10.75, 10.77
10.75 name
Wake up out time t/10

Analog Output 7

Footbrake Analog Output

# 0x392 1×1
No explanation exists yet.

From the official base maps what they contain, not what it does

Every official base map ships 0.

Detail
Address
0x1B44 6980
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Foot Brake Output Analog

Footbrake Analog Output Voltage Table

# 0x85A 1×2
No explanation exists yet.

From the official base maps what they contain, not what it does

All 16 official base maps are identical here, spanning 1.1 to 4.1.

Detail
Address
0x1B45 6981
Size
1×2 cells
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Foot Brake Output Voltage Table

Gear Position Analog Output

# 0x763 1×1
Picks which physical analog output (1-4, 0 = off) carries the gear voltage, using the voltages set in the Gear Output Voltage Table. Lets a dash or logger without CAN read the current gear as a 0-5V signal.
See also: Gear Position Analog Output Voltage Table
Detail

TurboLamik XDF

0 - OFF 1 - Analog Output 1 2 - Analog Output 2 3 - Analog Output 3 4 - Analog Output 4

From the official base maps what they contain, not what it does

Every official base map ships 1.

Address
0x17BD 6077
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Gear Out Analog

Gear Position Analog Output Voltage Park

# 10.77 only Vendor description only 0x6530 1×1

TurboLamik XDF

The voltage TCU send on choosen Analog Output for each specific gear.

Detail
Address
0x17BE 6078
Size
1×1 value
Width
8-bit
Firmware
10.77

Gear Position Analog Output Voltage Table

# 0x3E51 1×10
The voltage the analog gear output puts out for each position, one cell per gear from Reverse through 8th. This is what a voltage-input dash or logger decodes back into a gear number.
See also: Gear Position Analog Output · 0x3E63
Detail

TurboLamik XDF

The voltage TCU send on choosen Analog Output for each specific gear.

From the official base maps what they contain, not what it does

All 16 official base maps are identical here, spanning 0 to 4.5.

Indexed by columns 1 to 8 Gear in 10 steps.

Address
0x17BE 6078
Size
1×10 cells
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Gear Output Voltage Table

Parking Analog Output Voltage

# Vendor description only 0x2D0C 1×1

TurboLamik XDF

The voltage TCU will send

From the official base maps what they contain, not what it does

Every official base map ships 0.5.

Detail
Address
0x1F43 8003
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Parking Output Voltage

Torque Reduction Analog Output

# 0x4242 1×1
Puts the torque-cut request on one of the four physical 0-5V analog outputs (1-4, 0 = off) instead of an AUX pin or CAN. Analog Output 2 is pin 50.
Manual: Shift quality See also: 0x3131 · 0x3E63
Detail

TurboLamik XDF

0 - OFF 1 - Analog Output 1 2 - Analog Output 2 3 - Analog Output 3 4 - Analog Output 4 100% TQ Reduction = 0v 50% TQ Reduction = 2.5v 0% TQ Reduction = 5v

From the official base maps what they contain, not what it does

Official base maps ship 0 on 8HP45, 8HP50, 8HP51, 8HP75; 2 on 8HP70, 8HP90.

Address
0x1B58 7000
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Tourque Reduction Analog Out

EMU CAN 12

AC Clutch

# family 0x60A1 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 - OFF

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x17D5 6101
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

AC Fan

# family 0x371A 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 - OFF

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x17D6 6102
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

Coolant Fan

# family 0x58E0 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 - OFF

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x17D4 6100
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Colant Fan

Fuel Pump

# family 0x2520 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 - OFF

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x17D3 6099
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

Param. Output 1

# family 0x7310 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 to 20 - Virtual Aux 13-20

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x17CB 6091
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

Param. Output 2

# family 0x4787 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 to 20 - Virtual Aux 13-20

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x17CC 6092
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

Param. Output 3

# family 0x5BD6 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 to 20 - Virtual Aux 13-20

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x17CD 6093
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

Param. Output 4

# family 0x61FF 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 to 20 - Virtual Aux 13-20

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x17CE 6094
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

Param. Output 5

# family 0x67C6 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 to 20 - Virtual Aux 13 to 20

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x17CF 6095
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

Virt. Param. Out 1

# family 0x6CF1 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 to 20 - Virtual Aux 13 to 20

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x17D0 6096
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

Virt. Param. Out 2

# family 0x7220 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 to 20 - Virtual Aux 13 to 20

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x17D1 6097
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

Virt. Param. Out 3

# family 0x7817 1×1
Routes this signal to an AUX output pin: 1-12 picks the pin, 0 is off. Some pickers also offer virtual AUX 13-20 (CAN-side outputs with no physical pin). Check the pinout for what each AUX pin is wired to before assigning.
Manual: Wiring & pinout
Detail

TurboLamik XDF

0 - OFF 1 to 12 - Aux 1 to 12 13 to 20 - Virtual Aux 13 to 20

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x17D2 6098
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

Parametric Output 3

Invert Parametric Out 1

# 0x2714
Flips the polarity of Parametric Out 1, so the pin is active when the condition is false instead of true. Useful when the device on the other end expects the opposite sense.
See also: Seting Parametric Out 1 · Value Parametric Out 1
Detail

From the official base maps what they contain, not what it does

Off in all 16 official base maps.

Address
0x1EE5 7909
Width
8-bit
Mask
0x1
Firmware
10.75, 10.77

Seting Parametric Out 1

# 0x1265 6×1
A programmable output you build yourself. Pick the AUX pin (1-12 real, 13-20 virtual), then up to two input variables (analog channels, coolant temp, RPM, turbine speed, vehicle speed, gear, TPS, torque, footbrake and more), a comparison operator for each (lower than, greater than, equal and so on) and an OR/AND combiner. The pin switches when the condition is true.
See also: Value Parametric Out 1 · Invert Parametric Out 1
Detail

TurboLamik XDF

Aux Out; OFF: 0; Aux:1-12; Virtual AUX 13-20 Varible1,2: OFF: 0 Analog 1-12: 1-12 (Value mV) Engine CLT: 13 Program SW: 14 Engine RPM: 15 Turbine Speed: 16 RPM Outut: 17 Vehicle Seed: 18 Gear Actual: 19 Gear Target: 20 Aux 1-12: 21-32 TPS: 33 DBW: 34 Gearbox TQ: 35 Engine TQ: 36 Virtual Clutch: 37 SW Mux 1-3 38-40 Parametric 1-4: 41-44 Footbrake: 45 Neutral: 46 Parking: 47 T-Brake/Launch 49 continued in: Parame

From the official base maps what they contain, not what it does

Values differ between official base maps (2 distinct variants); across all 16 they span 0 to 33.

Address
0x1EAD 7853
Size
6×1 cells
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Setting Parametric Out 1

Value Parametric Out 1

# 0x60F5 2×2
The numbers for the parametric output condition: the value each of the two variables is compared against, plus a hysteresis band for each so the output does not chatter around the threshold.
See also: Seting Parametric Out 1 · Invert Parametric Out 1
Detail

TurboLamik XDF

Varible 1,2 Value: Value of the selected parameter Hist: Hysteresis of the selected parameter Operator 1,2: Lower Than: 0 Greatrt Then: 1 Equal or Lower Than: 2 Equal or Greatrt Then: 3 Equal to: 4 Logic Operator: OFF: 0 OR: 1 AND: 2

From the official base maps what they contain, not what it does

Values differ between official base maps (2 distinct variants); across all 16 they span 0 to 50.

Address
0x1EC5 7877
Size
2×2 cells
Width
16-bit
Firmware
10.75, 10.77

PWM1 9

DC Output ( x-axis)

# 0x435A 1×12
No explanation exists yet.

From the official base maps what they contain, not what it does

All 16 official base maps are identical here, spanning 8 to 98.

Detail
Address
0x1C7A 7290
Size
1×12 cells
Width
16-bit
Firmware
10.75, 10.77

DC Switch input

# 10.77 only Vendor description only 0x5FC8 1×1

TurboLamik XDF

0- off 1 to12- Analog 1 to 12

Detail
Address
0x1FBA 8122
Size
1×1 value
Width
8-bit
Firmware
10.77

DC1 Output

# 0x6985 1×12
No explanation exists yet.

From the official base maps what they contain, not what it does

All 16 official base maps are identical here, spanning 0 to 70.31.

Detail
Address
0x1D65 7525
Size
1×12 cells
Width
8-bit
Firmware
10.75, 10.77
10.75 name
DC Output

DC2 Output

# 10.77 only 0x6568 1×12
Not documented yet.
Detail
Address
0x1FBB 8123
Size
1×12 cells
Width
8-bit
Firmware
10.77

Frequency (Hz)

# 0x687E 1×1
Carrier frequency of the PWM1 output, 10 Hz to 3000 Hz. Set it to whatever the driven device (fan controller, AWD coupling) wants.
See also: Input parameter · PWM Output
Detail

TurboLamik XDF

10Hz-3000Hz

From the official base maps what they contain, not what it does

Official base maps ship 7.63 on 8HP50, 8HP51, 8HP70, 8HP75, 8HP90; 100 on 8HP45.

Address
0x1C53 7251
Size
1×1 value
Width
16-bit
Firmware
10.75, 10.77

Gearbox Fan DC

# 10.77 only 0x45A8 1×1
Not documented yet.
Detail
Address
0x1FB9 8121
Size
1×1 value
Width
8-bit
Firmware
10.77

Input parameter

# 0x74A3 1×1
What drives the PWM1 output: 0 off, 1 the AWD coupling duty, 2 engine coolant temperature. The duty-cycle curve itself lives in the DC Output table next to it.
See also: Frequency (Hz) · PWM Output
Detail

TurboLamik XDF

0- PWM OFF 1- AWD 2- Engine CLT/ gearbox temp fan control

From the official base maps what they contain, not what it does

Official base maps ship 0 on 8HP50, 8HP51, 8HP70, 8HP75, 8HP90; 2 on 8HP45.

Address
0x1C55 7253
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Input Parameter

invert DC Switch input

# 10.77 only 0x4FAE
Not documented yet.
Detail
Address
0x1EFD 7933
Width
16-bit
Mask
0x100
Firmware
10.77

PWM Output

# 0x2253 1×1
Picks the AUX pin that carries the PWM1 signal. Only AUX 9 to 12 are valid here; any other value leaves it off.
Manual: Wiring & pinout See also: Input parameter · Frequency (Hz)
Detail

TurboLamik XDF

0 - 8 OFF 9 to 12 - Aux 9 to 12 13 - OFF

From the official base maps what they contain, not what it does

Every official base map ships 0.

Address
0x1D64 7524
Size
1×1 value
Width
8-bit
Firmware
10.75, 10.77

Names and groups follow the TurboLamik XDF. Values are not published here: open your own .bin in Map Studio to see what your map actually holds, and verify anything you change against the official manual.