TurboLamik TurboLamik

Parameters / ECU Info

ECU Info

Identity and version fields the TCU reports about itself and the loaded calibration.

9 parameters: 5 documented, 4 not yet documented. 2 exist only on firmware 10.77.

9 parameters

7 Seg Brightness

# 10.77 only 0x7D1 1×1
Not documented yet.
Detail
Address
0x1FB8 8120
Size
1×1 value
Width
8-bit
Firmware
10.77

Enable LCD

# 0x43A4
No explanation exists yet.

From the official base maps what they contain, not what it does

On in all 16 official base maps.

Detail
Address
0xE73 3699
Width
8-bit
Mask
0x4
Firmware
10.75, 10.77

Enable Oil Temp (F)

# 0xB3F
No explanation exists yet.

From the official base maps what they contain, not what it does

Off in all 16 official base maps.

Detail
Address
0x1EFD 7933
Width
16-bit
Mask
0x40
Firmware
10.75, 10.77

LCD Gear Offset

# 10.77 only 0x3C60 1×1
Not documented yet.
Detail
Address
0x1F4F 8015
Size
1×1 value
Width
8-bit
Firmware
10.77

Logging frequency

# 0x11F1 1×1 Hz
Datalogging rate constant. The stored value X gives a logging frequency of 2000/X Hz, so smaller values log faster.
Detail

From the official base maps what they contain, not what it does

Official base maps ship 60.61 Hz on 8HP45, 8HP51, 8HP70; 80 Hz on 8HP75; 40 Hz on 8HP50, 8HP90.

Address
0x1799 6041
Size
1×1 value
Width
8-bit
Unit
Hz
Firmware
10.75, 10.77
10.75 name
logging frequency

TCU Date

# 0x4808 1×2
Production date of the unit. Read the settings down from the TCU first to populate it; informational only.
Detail

TurboLamik XDF

Production date, First read the settings from the TCU

From the official base maps what they contain, not what it does

Values differ between official base maps (3 distinct variants); across all 16 they span 0 to 23.

Address
0x8 8
Size
1×2 cells
Width
8-bit
Firmware
10.75, 10.77
10.75 name
ECU Date

TCU File: Transmission Type

# 0x562A 4×12
The bin's identity note: which gearbox the calibration is for (for example ZF8HP45/03V3), its software baseline, a date, and the fuel (ON = diesel, PB = petrol). Read this to confirm a map really matches your box; base maps differ by over a thousand values between boxes.
Manual: Software & config
Detail

TurboLamik XDF

Make sure using correct BIN file for correct transmission type, ex HP 45/50/51/70/75/76/90/95

From the official base maps what they contain, not what it does

Values differ between official base maps (16 distinct variants); across all 16 they span 45 to 120.

Indexed by columns 1 to 12 in 12 steps.

Address
0x1B14 6932
Size
4×12 cells
Width
8-bit
Firmware
10.75, 10.77
10.75 name
Note: Gearbox type

TCU FIRMWARE ID

# 0x2B19 1×1
The firmware baseline this calibration was built on, shown as a version number (TunerPro reads it under ECU Info as Software ID). Most official base maps are 10.75; the 8HP45 and 8HP90 maps still ship on the older 10.72 baseline, which decodes fine with the V10.75 definition.
Manual: Software & config
Detail

From the official base maps what they contain, not what it does

Official base maps ship 10.75 on 8HP50, 8HP51, 8HP70, 8HP75; 10.72 on 8HP45, 8HP90.

Address
0x2 2
Size
1×1 value
Width
16-bit
Firmware
10.75, 10.77
10.75 name
SW ID

TCU NAME

# 0x3BC7 2×12
A text field identifying the hardware family; official maps read "TURBO LAMIK TCU V2". Informational, nothing to set.
Detail

From the official base maps what they contain, not what it does

All 16 official base maps are identical here, spanning 32 to 86.

Indexed by rows 1 to 2 in 2 steps, columns 1 to 12 in 12 steps.

Address
0xC 12
Size
2×12 cells
Width
8-bit
Firmware
10.75, 10.77
10.75 name
ECU NAME

Names and groups follow the TurboLamik XDF. Values are not published here: open your own .bin in Map Studio to see what your map actually holds, and verify anything you change against the official manual.